The Alphacool “Lighttower” reservoir leads to a new way of design and function. Though most reservoirs are only compatible with one or few pumps, this reservoir can be used with multiple pumps or be used even without a pump. This maximum of flexibility comes from the intelligent construction. If the reservoir needs to be fixed with screws, there are already 4 M4 threads available in the bottom of the reservoir (screws must be ordered separately)
In the image you can see 2 threads on the right side. The lower one is the inlet. From there the water flows into the inside tube, then to the top of it and from there with multiple small spots to the inside wall of the big outside tube to run down to the water basin. With the intelligent construction (LED light coming from the bottom of the reservoir), you can achieve a new modding highlight looking like a lighttower inside. The lightning module you need in the botton is already included (LEDs must be ordered separately)
If you do not want to use this function you can use one thread above as inlet, so that the water runs into the reservoir from the bottom. Furthermore you can use that thread as outlet (for example if you do not want to use it with a pump and you want to have inlet and outlet at the same side of the reservoir) or use it for additional LED lightning or temperature sensors.
The fluid is collected in the bottom of the reservoir and due to the multiple hole plate the air goes out of the water very fast and the any cyclone or vortex is avoided. Under the hole plate is an additional basin where the water is stored and sucked from the pump. There is a big G1” thread in which multiple pump adaptors can be screwed.
The top can be unmounted for filling and refilling or the top can be connected with a fillport (fillport not included). This allows an easy and fast filling of the water cooling system.
List of pump compatibility:
Already included are 3 adaptors, so that this reservoir can be used with the following pumps:
Eheim 1046/1048 and Aquastream, Alphacool 1046
Additionally you can order these adaptors separately:
Alphacool Lighttower adaptor for G1/4 (Art. 46181)
Alphacool Lighttower adaptor for Eheim 1260 (Art. 46182)
Alphacool Lighttower Adapter für Hydor L30 II (Art. 46183)
Alphacool Lighttower adaptor for Alphacool VPP655 / Laing D5 (Art. 46184)
Type of reservoir: Tube reservoir
Pump compatibility: Phobya DC-12-220/260 Phobya DC12-400 Eheim 1046/1048
Material: POM / Plexi
Color: black / transparent
Volume: app. 250ml
Content of delivery:
1x Lighttower reservoir
2x Screw plug G1/4
1x Lightning module for 5mm LED
3x pump adaptor
This product has been reviewed for you:
Note: The Light Tower can also expand in height by replacing the tube or by means of Connector (Art. 46143/46144) expands the tube.
Attention: The manufacturer Mayhems advises that Mayhems fluids, especially the Aurora line of products, have been manufactured and distributed solely for show and modding purposes. These should not be utilized in the system for more than 14 days.
We would also like to advise that Mayhems fluids can damage water cooling products, and using Mayhems fluids can thereby void the warranties offered by the following manufacturers: Koolance, Phobya, Alphacool, Aqua Computer, Watercool.
Damages such as: clogging, corrosion of aluminium radiators, deterioration of glued containers, etc., are a consequence of the use of Mayhems, but will not be reimbursed by Mayhems. Use is therefore at one’s own risk.
|Pump compatibility:||For flow pumps|
|Connector:||G1/4" inner thread|
|Number of connections:||3|
|Fillport:||G1/4" inner thread|
|LED hole:||Not available|
|Model of reservoir:||Tubing - reservoirs 60mm|
|Dimensions:||60 x 60 x 165mm|
Clicca qui per visualizzare questa domanda (s).
Clicca qui per vedere queste valutazioni.
Bin soweit zufrieden. Was ich mir nur gewünscht hätte wäre ne möglichkeit den AGB an einen 140mm Lüfter Gehäuse platz zu montieren dies musste ich mir nach bestellen. Besonders gefällt mir wenn die Flüssigkeit nach Oben fliehst und raus kommt wie ein springbrunnen.
Der Lighttower war als Ersatz für eine großere Röhre gedacht, um wieder Platz an der Grafikkarte zu bekommen und die notwendigen Schlauchverbindung zur Pumpe wegzulassen. Der Lighttower sitzt dirket auf der Innovatek HPPS Pumpe. D Optisch ein schönes Produkt. Macht einen wertigen Eindruck.
Qualität 1a. Sieht einfach großartig aus.