|Connector:||G1/4" inner thread|
|Fillport:||G1/4" inner thread|
|LED hole:||Not available|
|Model of reservoir:||Tubing - reservoirs 60mm|
|Pump compatibility:||For 1x D5|
|Number of connections:||4|
The Eisbecher D5
This Eisbecher is the big brother of the D5 version. The pump can be attached using a mounting ring and eight screws to hold it. The plexiglass version can be illuminated with four LEDs, which are placed into the pump socket. The lighting module illuminates from above. Small riser pipes and Bubble Down also do their work faultlessly here. The Eisbecher can be mounted either with the mounting bracket or with the included stands. If there is room in the 3.5" hard drive cage inside the case, the pump socket also has threads for this (requires pump decoupling with M4 inner and outer threads - Art. no. 52007).
Scope of Delivery
- 8x M4x12mm screws
- 8x M4x8mm screws
- 4x M4 nuts
- 1x mounting ring
- 1x O-ring ID ca. 54mm
- 2x stands
- 1x 2.5mm hex key
Dimensions for 150mm version
- Dimensions incl. bracket without stands (LxWxH): 176 x 136 x 80mm
- Dimensions without bracket incl. stands (LxWxH): 223.5 x 87.5 x 80mm
- Plexiglass tube diameter: 60mm
- Capacity: 180ml
The VPP755 Eispump
The Alphacool VPP755 Eispump improves on the classic D5 VPP655 pump in every way. There is no area where it is weaker or louder than its predecessor, and it instead offers new ways to control the pump to your liking.
- Dimensions (DxH): 60 x 53.5mm
- Cable length: 50cm
- Standard voltage: 12V DC
- Power consumption: 14W
- Permitted voltage: 8-13V DC
- Pressure at 12V: 4m water head
- Maximum flow rate: 350l/h
- Pump medium: water, water/glycol mixture
- Maximum system temperature: 65ºC
- Power connection: 4-pin molex
- Tach signal: 3-pin
- PWM signal: 4-pin
- Special feature: adjustable in five levels
- Level 1: 1800 RPM
- Level 2: 2500 RPM
- Level 3: 3200 RPM
- Level 4: 3900 RPM
- Level 5: 4500 RPM
Scope of Delivery
- Alphacool Eisbecher D5 150mm Acetal incl. 1x Alphacool Eispump VPP755
In order to use the inlet from above, a G1/4" extension piece is required (art. no. 1011183-1011186), as the thread is embedded a few mm into the cap and many screw threads will not be able to reach it.
Removing the impeller from the ceramic shaft will cause the upper ceramic clamping ring to over-expand, which will destroy it! Removal will void the pump’s warranty!
If the pump is put together again and put back into operation, the clamping ring will loosen, which is not accepted as grounds for a return or exchange...
Attention: The manufacturer Mayhems advises that Mayhems fluids, especially the Aurora line of products, have been manufactured and distributed solely for show and modding purposes. These should not be utilized in the system for more than 14 days.
We would also like to advise that Mayhems fluids can damage water cooling products, and using Mayhems fluids can thereby void the warranties offered by the following manufacturers: Koolance, Phobya, Alphacool, Aqua Computer, Watercool.
Damages such as: clogging, corrosion of aluminium radiators, deterioration of glued containers, etc., are a consequence of the use of Mayhems, but will not be reimbursed by Mayhems. Use is therefore at one’s own risk.
Clicca qui per vedere queste valutazioni.
I know the pump since several months. Now with this reservoir the price is so good! I whished I had known this product combination instead of ordering my reservoir and pump as 2 products. This is at least 10$ cheaper